Apache 2.x on Microsoft Windows
This section contains notes and hints specific to Apache 2.x installs
of PHP on Microsoft Windows systems. We also
have instructions and notes
for Apache 1.3.x users on a separate page.
You should read the manual
installation steps first!
Apache 2.2 Support
Users of Apache 2.2 should note that the DLL file for Apache 2.2 is
named php5apache2_2.dll rather than php5apache2.dll
and is available only for PHP 5.2.0 and later.
See also » http://snaps.php.net/
You are strongly encouraged to consult the
» Apache Documentation to get
a basic understanding of the Apache 2.x Server. Also consider
reading the » Windows specific
notes for Apache 2.x before reading on here.
Apache 2.x is designed to run on the Windows version designated as
server platforms, such as Windows NT 4.0, Windows 2000,
Windows XP, or Windows 7. While Apache 2.x works tolerably well on Windows 9x,
support on these platforms is incomplete, and some things will not work
correctly. There is no plan to remedy this situation.
Download the most recent version of »
Apache 2.x and a fitting PHP version.
Follow the Manual Installation
Steps and come back to go on with the integration of PHP and Apache.
There are three ways to set up PHP to work with Apache 2.x on Windows.
You can run PHP as a handler, as a CGI, or under FastCGI.
Nota: Ricordare che quando si aggiungono
valori di path nei file di configurazione Apache su Windows, tutti i backslash
some c:\directory\file.ext devono essere convertiti in
slash, come c:/directory/file.ext. Uno slash
finale può essere necessario per le cartelle.
Installing as an Apache handler
You need to insert the following lines into your
Apache httpd.conf configuration file to load the
PHP module for Apache 2.x:
Example #1 PHP and Apache 2.x as handler
LoadModule php5_module "c:/php/php5apache2.dll"
AddHandler application/x-httpd-php .php
# configure the path to php.ini
Remember to substitute your actual path to PHP for the
C:/php/ in the above examples. Take care to use
either php5apache2.dll or
php5apache2_2.dll in your LoadModule directive and
verify that the referenced file is in fact located at the file path
that you point to in this directive.
The above configuration will enable PHP handling of any file that has a
.php extension, even if there are other file extensions. For example, a
file named example.php.txt will be executed by the
PHP handler. To ensure that only files that end in
.php are executed, use the following configuration
Running PHP as CGI
You should consult the » Apache CGI
documentation for a more complete understanding of running CGI
To run PHP as CGI, you'll need to place your php-cgi files in a
directory designated as a CGI directory using the ScriptAlias directive.
You will then need to insert a #! line in the PHP files, pointing to the
location of your PHP binary:
Example #2 PHP and Apache 2.x as CGI
Usando il setup del CGI, il server
è aperto a parecchi attacchi. Leggere la
sezione sulla sicurezza CGI per capire come
difendersi da quest attacchi.
Running PHP under FastCGI
Running PHP under FastCGI has a number of advantages over running it as a
CGI. Setting it up this way is fairly straightforward:
Obtain mod_fcgid from
» http://httpd.apache.org/mod_fcgid/. Win32
binaries are available for download from that site. Install the module
according to the instructions that will come with it.
Configure your web server as shown below, taking care to adjust any paths
to reflect your how you have installed things on your particular system:
Example #3 Configure Apache to run PHP as FastCGI
LoadModule fcgid_module modules/mod_fcgid.so
# Where is your php.ini file?
FcgidInitialEnv PHPRC "c:/php"
AddHandler fcgid-script .php
FcgidWrapper "c:/php/php-cgi.exe" .php
Files with a .php extension will now be executed by the PHP FastCGI